Loading effect correction for real-time aethalometer measurements of fresh diesel soot

In this study, a correction was developed for the aethalometer to measure real-time black carbon (BC) concentrations in an environment dominated by fresh diesel soot. The relationship between the actual mass-specific absorption coefficient for BC and the BC-dependent attenuation coefficients was determined from experiments conducted in a diesel exposure chamber that provided constant concentrations of fine particulate matter (PM; PM(2.5); PM < 2.5 microm in aerodynamic diameter) from diesel exhaust. The aethalometer reported BC concentrations decreasing with time from 48.1 to 31.5 microg m(-3) when exposed to constant PM(2.5) concentrations of 55 +/- 1 microg m(-3) and b(scat) = 95 +/- 3 Mm(-1) from diesel exhaust. This apparent decrease in reported light-absorbing PM concentration was used to derive a correction K(ATN) for loading of strong light-absorbing particles onto or into the aethalometer filter tape, which was a function of attenuation of light at 880 nm by the embedded particles.     

In field arsenic removal from natural water by zero-valent iron assisted by solar radiation

An in situ arsenic removal method applicable to highly contaminated water is presented. The method is based in the use of steel wool, lemon juice and solar radiation. The method was evaluated using water from the Camarones River, Atacama Desert in northern Chile, in which the arsenic concentration ranges between 1000 and 1300 μg L⁻¹. Response surface method analysis was used to optimize the amount of zero-valent iron (steel wool) and the citrate concentration (lemon juice) to be used. The optimal conditions when using solar radiation to remove arsenic from natural water from the Camarones river are: 1.3 g L⁻¹ of steel wool and one drop (ca. 0.04 mL) of lemon juice. Under these conditions, removal percentages are higher than 99.5% and the final arsenic concentration is below 10 μg L⁻¹. This highly effective arsenic removal method is easy to use and inexpensive to implement.     

Arsenic chemistry in the rhizosphere of Pteris vittata L. and Nephrolepis exaltata L

This greenhouse experiment evaluated the influence of arsenic uptake by arsenic hyperaccumulator Pteris vittata L. and non-arsenic hyperaccumulator Nephrolepis exaltata L. on arsenic chemistry in bulk and rhizosphere soil. The plants were grown for 8 weeks in a rhizopot with a soil containing 105 mg kg(-1) arsenic. The soil arsenic was fractionated into five fractions with decreasing availability: non-specifically bound (N), specifically bound (S), amorphous hydrous-oxide bound (A), crystalline hydrous-oxide bound (C), and residual (R). P. vittata produced larger plant biomass (7.38 vs. 2.32 mg plant(-1)) and removed more arsenic (2.61 vs. 0.09 mg pot(-1) arsenic) than N. exaltata. Plant growth reduced water-soluble arsenic, and increased soil pH (P. vittata only) in the rhizosphere soil. P. vittata was more efficient than N. exaltata to access arsenic from all fractions (39-64% vs. 5-39% reduction). However, most of the arsenic taken up by both plants was from the A fraction (67-77%) in the rhizosphere soil, the most abundant (61.5%) instead of the most available (N fraction).     

Long-term study of environmental levels of dioxins and furans in the vicinity of a municipal solid waste incinerator

From 1975 to 2004, a municipal solid waste incinerator (MSWI) was operating in Montcada (Barcelona, Catalonia, Spain). Because of the potential health risks derived from emission of pollutants by the facility, especially polychlorinated dibenzo-p-dioxins (PCDDs) and dibenzofurans (PCDFs), a long-term monitoring program focused on measuring the environmental levels of PCDD/Fs near the facility, and to assess the health risks for the population living in the neighborhood, was established between 1996 and 2002. A total number of 111 soil and 121 herbage samples were analyzed for PCDD/Fs during this period. Human health risks for the individuals living near the MSWI (500 and 1,000 m) were also assessed before (1998) and after modernization (2000) of the facility. It included PCDD/F inhalation, dermal contact, soil and dust ingestion, and food intake. All these data are here summarized. The environmental levels of PCDD/Fs showed that the MSWI was not the main responsible of the atmospheric pollution by these compounds. In turn, human health risks for the population living in the vicinity of the facility after introduction of a modern technology were negligible in comparison with the dietary PCDD/F exposure.     

Environmental Impact Assessment of Polylactide(PLA)/Chicken Feathers Biocomposite Materials

The aim of this study is to analyse the environmental impacts (EIs) of the process of preparation of new biocomposite materials obtained from polylactide (PLA) and chicken feathers (CFs). Two CFs stabilization methods and different percentages of CFs have been studied. The EIs of these new composites were compared to the impact of virgin PLA. Cradle-to-gate life cycle inventories were assessed for 0–35% v/v of CFs in a CFs/PLA biocomposite. Two CFs stabilization processes, autoclave and surfactant, were tested and compared with the aim to prioritize one of them from the environmental point of view. A composite plate of 184?×?184?×?2.2 mm³ was defined as the functional unit. Autoclave stabilization process exhibited lower environmental impact compared with surfactant stabilization process mainly due to both the lower requirements of electricity and water and the reduced pollution loads of the generated wastewater. Thus, the autoclave process was selected as the standard method when comparing the EIs of the proposed CFs/PLA biocomposites. In this sense, the addition of CFs to PLA matrix proportionally reduces all the EIs compared to pure PLA due to the replacement of PLA with CFs. This behaviour can be explained because the PLA production accounts for the 99% of the impact of the biocomposite. Consequently, CFs conveniently stabilized might be an alternative raw material to prepare CFs/PLA biocomposites with less environmental impact compared to pure PLA.     

Discerning the factors explaining the change in energy efficiency

Due to the high rates of energy consumption and its impact on environment over the last decades, policy decision-makers are increasingly recognising the need to take actions that allow to address problems associated with the deployment of non-renewable resources and climate changes. One field of action has been the promotion of measures that contribute to improve energy efficiency of countries. The purpose of this study is to identify the main factors explaining changes in energy efficiency applying the multiplicative Log Mean Divisia Index decomposition method for a set of countries (Portugal, UK, Brazil and China) with different socio-economic background and energy mix. The results show that overall energy efficiency trends display different patterns between countries and the same happens within each country from a sectoral perspective. Major drivers of improvements of overall energy efficiency were the intensity effect and the affluence effect, whereas the driver that hampered those improvements was the energy consumption per capita. Some policy implications derived from the results achieved are: policy decision-makers should support measures that promote the adoption of energy-saving technologies resulting from new technological developments; policy measures should be directed to raise awareness of end-users regarding energy efficiency and energy conservation efforts; policy measures promoting economic growth through the development (or expansion) of sectors of activity that consume less energy can also be implemented; finally, policy instruments may also be used to reduce the costs of implementing energy efficiency and energy-saving measures to households and firms.     

1,4-Dioxane removal from water and membrane fouling elimination using CuO-coated ceramic membrane coupled with ozone

Environmental Science and Pollution Research - 1,4-Dioxane is a synthetic cyclic ether traditionally used as a chlorinated solvent stabilizer. It is a small molecule and recalcitrant compound that...     

Improving ozonation to remove carbamazepine through ozone-assisted catalysis using different NiO concentrations

The carbamazepine (CBZ) abatement is herein evaluated using catalytic ozonation at different NiO concentrations as catalyst: 100, 300, and 500 mg